6 kJ/s High Voltage Power Supplies

General Atomics Energy Products, a Division of General Atomics Electronic Systems

CCS06 SERIES
POWER SUPPLIES
6 kJ/s, 2 - 50 kV

6 kJ/s Power Supplies
The CCS06 Series of high voltage switching power supplies is designed to quickly charge capacitors, either small capacitances at high repetition rates, or large capacitor banks at low repetition rates. Our high frequency switchmode technology provides a compact and lightweight reliable power supply with a constant current, linear charging profile.

The many standard features and options make this series useful for laboratory and commercial applications such as lasers, medical accelerators, pulse generators, and high voltage test facilities. Designed for continuous use, these air-cooled power supplies provide an average charging rate of 6 kJ/s over 14 output voltage ranges from 2 kV to 50 kV, with either positive or negative output polarity. Output control and status monitoring are accomplished with the standard remote control interface. They can be ordered with or without instrumentation.

Model Number ¹	Output Power ²	Output Voltage	Output Current
CCS06002P1C	6 kJ/s	0 - 2 kV	6 A
CCS06003P1C	6 kJ/s	0 - 3 kV	4 A
CCS06004P1C	6 kJ/s	0 - 4 kV	3 A
CCS06005P1C	6 kJ/s	0 - 5 kV	2.4 A
CCS06006P1C	6 kJ/s	0 - 6 kV	2 A
CCS06007P1C	6 kJ/s	0 - 7 kV	1.7 A
CCS06008P1C	6 kJ/s	0 - 8 kV	1.5 A
CCS06010P1C	6 kJ/s	0 - 10 kV	1.2 A
CCS06015P1C	6 kJ/s	0 - 15 kV	0.8 A
CCS06020P1C	6 kJ/s	0 - 20 kV	0.6 A
CCS06025P1C	6 kJ/s	0 - 25 kV	0.48 A
CCS06030P1C	6 kJ/s	0 - 30 kV	0.4 A
CCS06035P1C	6 kJ/s	0 - 35 kV	0.34 A
CCS06040P1C	6 kJ/s	0 - 40 kV	0.3 A
CCS06045P1C	6 kJ/s	0 - 45 kV	0.27 A
CCS06050P1C	6 kJ/s	0 - 50 kV	0.24 A

¹Positive polarity, instrumented, 208 VAC 3Ø input. Other configurations available.
²Average power at maximum output voltage.

CCS06 Specifications

Average Charging Rate
6 kJ/s at rated Output Voltage

AC Input
208 VAC 3Ø 50/60 Hz
400 VAC 3Ø 50/60 Hz
480 VAC 3Ø 50/60 Hz

Voltage Ranges
2, 3, 5, 6, 8, 10, 15, 20, 25, 30, 35, 40,
45, 50kV. All models continuously variable
from 0 to 100% rated voltage output.
Accuracy ± 0.5%

Polarity
Positive or Negative (factory set)

Delay After Discharge
Preset PS off-time of ~ 150 µs after load
discharge to assist HV switch recovery
(factory tailorable)

Self Protected
Overvoltage/open circuit
Overcurrent (inherent in topology)
Overtemperature

Viewset
LCD display of programmed voltage set point

Pulse to Pulse Repeatability
± 0.5% to 1 kHz

Efficiency
> 90%

Power Factor
> 0.85

Inrush Current Limit
< 10A

Ambient Temperature
Operating: 0 to 45°C
Storage: -30 to 85°C

Size
222mm tall x 482mm x 508mm deep
8.75" tall x 19" x 20" deep

Weight
< 10kV, 19 kg (42 lbs)
10-50kV, 29 kg (64lbs)

Remote Control
25-pin D-type subminiature female
socket type connector

Output Cable
18 ft HV (other lengths available upon request)

Options

Chassis slides - user installable
Remote voltage sensing (<10 kV Models) - factory Installed
Master/Slave Option (1 for each slave) - user installable
Delay After Discharge custom configuration - factory installed
HV Inhibit Mode: Inhibit Active Low, Logic "0" = HV inhibited - factory installed
HV Enable Mode: Enable Active High, Logic "1" = HV enabled - factory installed
HV Enable Mode: Enable Active Low, Logic "0" = HV enabled - factory installed

Application Questionnaire | Voltage Reversal Protection | Operations & Maintenance Manual

Specifications are subject to change without prior notice.